Failures - История изменений

Thyristor chick в 17:03, 11 сентября 2018

2018-09-11T17:03:18Z

Thyristor chick в 16:55, 11 сентября 2018

2018-09-11T16:55:02Z

Thyristor chick в 16:47, 11 сентября 2018

2018-09-11T16:47:04Z

Thyristor chick в 15:45, 31 августа 2018

2018-08-31T15:45:46Z

Thyristor chick: /* RVTB braking (81-722) */

2018-08-30T10:13:11Z

RVTB braking (81-722)

Thyristor chick: /* E, Em508, Ezh, Ezh3 */

2018-08-29T14:02:47Z

E, Em508, Ezh, Ezh3

Thyristor chick в 11:01, 29 августа 2018

2018-08-29T11:01:09Z

Thyristor chick: Added emergency driving and other hotfixes

2018-08-29T11:00:34Z

Added emergency driving and other hotfixes

Thyristor chick в 09:46, 29 августа 2018

2018-08-29T09:46:51Z

Thyristor chick: Added failures for some trains and fixed mistakes in some places

2018-08-28T22:06:02Z

Added failures for some trains and fixed mistakes in some places

@@ Строка 2: / Строка 2: @@
 | lang = en
 | title = Failures
-| ru = Failures/ru
+| ru = Неисправности
 | en = Failures
 | de = Failures/de

@@ Строка 2: / Строка 2: @@
 | lang = en
 | title = Failures
 | en = Failures
 | de = Failures/de

@@ Строка 3: / Строка 3: @@
 | title = Failures
 | en = Failures
 | kr = Failures/kr
 }}

@@ Строка 94: / Строка 94: @@
 *Close EPV(EPK), then disable ARS.
 *Move reverser to neutral, pull it out (Shift + 7).
 *Pull reverser in {{tooltip| KRU | Emergency Control Handle}} shaft (Shift + 8).
 *Move reverser to position 1 or 2 - these are Driving positions.

@@ Строка 21: / Строка 21: @@
 ** Note: if it started and you didn't hold pedal, then you just need to start holding it again, so the air must stop leaking.
-'''THERE IS A WAY TO DISABLE RVTB''', to do this, you need a dispatcher permission to break seal on this valve, then disable it.
+'''THERE IS A WAY TO DISABLE RVTB''', to do this, you need a dispatcher permission to break seal on RVTB valve, then disable it.
 == Autostop braking ==

@@ Строка 140: / Строка 140: @@
 ===E, Em508, Ezh, Ezh3===
-'''Currently (before Metrostroi 2018 update) emergency mode on these type of trains doesn't work.'''
+'''Currently (before Metrostroi 2018 update) emergency mode on these types of trains doesn't work.'''
 [[Category:Driving]]

@@ Строка 91: / Строка 91: @@
 {{Important|Always inform a dispatcher, when you switch to emergency mode! Once you enabled it, you must disembark passengers on nearby station!}}
 ''These instructions presume the train is already set up and able to drive''
-==81-717==
+===81-717===
 *Close EPV(EPK), then disable ARS.
 *Move reverser to neutral, pull it out (Shift + 7).
@@ Строка 102: / Строка 102: @@
 **Note: before switching KRU to 0, close EPV(EPK) and disable ARS switch.
-==81-720 "Yauza"==
+===81-720 "Yauza"===
 *If you need to enable emergency BBE, then:
 **Disable BBE and enable Emergency BBE.
@@ Строка 129: / Строка 129: @@
 **Drive with Emergency X1 and Emergency X2 buttons on RV panel (or by using hotkeys). Brakes engage with KTR brake and release buttons (or with emergency brake valve).
-==81-722==
+===81-722===
 {{Important|In this case you need to break seals, so you must contact dispatcher for permission}}
 *Switch Movement Direction to 0.
@@ Строка 139: / Строка 139: @@
 *Drive with AH button on the left side. Brake with brake valve.
-==E, Em508, Ezh, Ezh3==
+===E, Em508, Ezh, Ezh3===
 '''Currently (before Metrostroi 2018 update) emergency mode on these type of trains doesn't work.'''
 [[Category:Driving]]

@@ Строка 60: / Строка 60: @@
 *If you need to switch to ALS mode, where you can see an ALS speedlimit, but you can exceed it, then:
 **Break the seal on ALS cover and press the button.
-*If you need to turn off both blocks of BARS, then:
+**ALS mode is now on.
-**Break the seal on "BARS block" switch and switch to "BARS 1+2" mode (just pressing the (+) on switch, until it stops turning)
+*If you need to disable (block) both units of BARS, then:
 **Break the seal on KAH cover and press the button.
 ***Note: you can drive lower than 20 km/h, to exceed this speed, you need to switch to ALS mode.
@@ Строка 86: / Строка 88: @@
 ==Emergency driving==
 [[Category:Driving]]

@@ Строка 69: / Строка 69: @@
 *Break the seal on RC-ARS(ARS disconnect) and enable it.
 *ARS is now disabled.
-**Note: You will need to hold the antetion pedal to prevent RVTB start leaking (Unless "Driving w/o attention pedal" is enadled).
+**Note: You will need to hold the antetion pedal to prevent RVTB start leaking (Unless "Driving w/o attention pedal" is enabled).
 ===Ezh===

@@ Строка 6: / Строка 6: @@
 }}
-== EPV(EPK) braking ==
+== EPV(EPK) braking (81-717, E, Em508, Ezh, Ezh3)==
 If you hear an air leak it can be EPV(EPK) braking, so you need to restart the ARS system - close EPV(EPK), disable ARS, wait 3-10 seconds, enable ARS, open EPV(EPK)
 '''To prevent an EPV(EPK) braking:'''
-# Open EPV(EPK) ONLY after switching on the ARS
+* Open EPV(EPK) ONLY after switching on the ARS.
-# If you need to change a reverse: close EPV(EPK), disable ARS, change reverse, enable ARS, open EPV(EPK).
+* If you need to change a reverse: close EPV(EPK), disable ARS, change reverse, enable ARS, open EPV(EPK).
 == Autostop braking ==
-* Return autostop bracket:
+===81-722===
-# Apply an emergency brake
+* Turn movement direction to 0
-# Press "Reset Contacts" button below the right window, right from the UAVA.
+* Wait until air stops leaking (about 5-7 seconds)
-{{Important|You must press '''"Reset Contacts"''' button, '''NOT "Disable UAVA"''' lever!}}
+* Turn movement direction to direction you need
 == Loss of direction signal ==
@@ Строка 39: / Строка 57: @@
 **Note: You will need to hold the attention pedal to drive (Unless VAH is enabled)
-===81-720 (Yauza)===
+===81-720 "Yauza"===
-*Break the seal on the ALS Button Cover, and press the button.
+*If you need to switch to ALS mode, where you can see an ALS speedlimit, but you can exceed it, then:
-*Break the seal on the KAH Button Cover, and press the button.
+**Break the seal on ALS cover and press the button.
-*ARS is now disabled.
+*If you need to turn off both blocks of BARS, then:
 ===81-722===
-(Coming soon)
+*Disable ARS/ALS
 ===Ezh===
 ===Ezh3===
-*Close EPV(EPK), then disable ARS/ALS.
+*Close EPK, then disable ARS/ALS.
-*Break the seal on RC-ARS (ARS disconnect) and enable it.
+*Break the seal on RC-ARS and enable it.
 *ARS is now disabled.
-**Note: You will need to hold the attention pedal to drive
+**Note: You will need to hold the attention pedal to drive.
 [[Category:Driving]]